The Télé’Son S63 kit is an electronic board for fitting out your own Socotel S63 telephone, desk or wall-mounted. It is a standalone audio player that plays the sounds stored on a microSD card (sold separately), in MP3 and WAV formats. Find it here, in the shop.
Do you have a Socotel U43? It has its own manual: Télé'Son U43 kit.
Quick overview

This board lets you fit out a Socotel S63. It carries an audio file player that plays the sounds on a microSD card, in MP3 (recommended) and WAV (up to 48 kHz / 16 bits) formats, as soon as the handset is picked up, the dial is turned or the keys are used (depending on your installation and your settings).
The components are already soldered, except the hook switch: you solder the one from your own telephone. The Nano is already programmed. The telephone and the installation work are not included.
Fully equipped models are regularly for sale in the BigSoundBank shop. If none is available, contact me: I have some in stock, and I can even fit out your own telephones to order.
I made this board myself. Research and development, circuit board design, right down to soldering the components: it is all done by my own hands.
Fitted with an Arduino "Nano" type microcontroller, it can be reprogrammed by the more hands-on among you, to make it do whatever you like. Here are a few examples of what it can do:
- A "Quiz'O'Phone" with a single question or several questions, Christmas special.
- An escape game prop.
- An old, poetic hotel telephone.
- Etc.
If you are really hands-on and want to build your own installation from A to Z, follow this tutorial.
Warning
Caution: the board is sold without a case. Install it in the telephone before powering it: nothing conductive must touch it, or there is a risk of a short circuit. It is powered only through its 7 to 16 V socket: 230 V mains electricity is dangerous, never connect it to the board.
In detail

Legend
The diagram shows the V5 board, as it is delivered in the kit. Some footprints are left empty: they are used on the fully equipped Télé'Son (mains module, mains input, bell and microphone), or for an old "3W" socket.
- 1: power socket, 7 to 16 V (5.5 × 2.1 mm DC plug).
- 2: microSD card reader.
- 3: hook switch footprint ("COMBINE-D2"), where you solder the one from your telephone.
- 4: "ROTATIF" screw terminal, for the rotary dial.
- 5: "CLAVIER" screw terminal, for the push-button keypad.
- 6: the six setting switches.
- 7: volume.
- 8: handset and earpiece lugs ("−", "+" and "MIC").
- 9: "LINE" jack socket, for headphones or an amplifier.
- 10: ringer relay.
Explanations
Power supply
The board is powered through its socket 1, between 7 and 16 V, with a standard DC plug (5.5 × 2.1 mm, known as "DC5521"), + in the centre. I recommend 9 V, which produces less heat: from the mains with a DC power supply, or with a battery box (rechargeable batteries recommended, or ordinary batteries). The socket is protected against reversed wires.
To power several Télé'Son from a single power supply, use a DC splitter. An extension cable lets you move the power supply further away.
Files
The reader 2 accepts a microSD card of up to 32 GB, formatted in FAT16 or FAT32. Put your sounds in a folder named mp3, at the root of the card, and name them 0001, 0002, 0003… without skipping a number: dialling "23" plays file 0023. The order in which you copy them does not matter, it is the name that counts. The file with the highest number is used as the intro (switch 3). Do not put anything else on the card.
On a Mac, hidden "._" files are added, which the player counts as sounds: type dot_clean /Volumes/CARD_NAME in the Terminal to delete them.

Handset, dial and keypad
The Nano knows when the handset is picked up thanks to the hook switch, the one from your own telephone, soldered onto the "COMBINE-D2" footprint 3.
A Socotel S63 can have a rotary dial or a push-button keypad. The dial is screwed into the "ROTATIF" terminal 4, the keypad into the "CLAVIER" terminal 5, and switch 6 tells the program which of the two is connected. The "CLAVIER" terminal expects a keypad wired as a matrix (3 columns and 5 rows). Some original keypads are not: for them, there is an S63 Keypad Board, onto which your original keys clip (see "The S63 Keypad Board", in step 6 of the installation).
The six switches
On the board, a red block 6 holds six small white switches. It is read from the nearest edge of the telephone: stand on that side, and switch 1 is then on the left and switch 6 on the right. Pushed up (towards the centre of the board and the markings A1 to A6), a switch is "ON"; pushed down, it is "OFF". Here is what they do:
- 1 Ringer: leave it OFF (see "Ringer" below).
- 2 Files played at random (OFF) or in order (ON).
- 3 No intro file (OFF), or back to the intro file, the last one on the card, when the handset is picked up and when a number that does not exist is dialled (ON).
- 4 Only one file is played each time the handset is picked up (OFF), or they follow one another automatically until the handset is hung up (ON).
- 5 Numbering disabled: each number dialled plays the next file (OFF); or enabled: if you dial 23, file 0023 is played (ON).
- 6 Rotary dial (OFF) or push-button keypad (ON).

Change the settings with the telephone unplugged, then plug it back in.
Volume
The volume is set by hand, by turning the shaft of the small potentiometer 7. It acts on all the outputs.
Listening
You usually listen through the handset (mono), whose wires are screwed onto the lugs 8: blue on "−", red on "+". If your telephone has one, the extra earpiece (a red wire and a blue wire) connects to the same place (mono as well). The two green microphone wires are screwed onto the "MIC" lugs: on the kit, they are not connected to anything, they are only there to hold these wires so that they do not wander around inside the telephone.
You can also plug one or more headphones (with a splitter), an active speaker or an amplifier into the "LINE" jack socket 9, in stereo. Both outputs work at the same time. The handset output is bridged: never connect its wires to a ground, nor to the input of an amplifier.

Ringer
A Socotel's ringer runs on 230 V AC, far too dangerous for an amateur. The kit's board carries the ringer relay 10 and its protection, but no terminal: wiring it is a job for an electrician. If it matters to your eyes (ears?), buy my fully equipped, ready-to-use Télé'Son S63 or U43: they ring.
Step-by-step installation

Step 1: preparation
Get hold of an old Socotel S63 telephone, desk or wall-mounted.
Step 2: dismantling
All the screws are underneath the telephone: work on a tea towel laid on a table, and turn the telephone over, taking care not to drop the handset (or the earpiece) and not to scratch it. Open it by undoing the two screws underneath, then empty it completely, keeping all the loose parts: screws, lugs and hook switch.
Step 3: cleaning
Clean the shell and the parts with a damp sponge or a cloth, to remove dust and marks. Do not use an abrasive sponge, like the green side of a kitchen sponge: it scratches the plastic.
Step 4: anti-theft (optional)
On a desk S63, the anti-theft sling (sold separately) goes through the round plastic post in the base, which the kit's circuit board is shaped to avoid. If the post has no hole, drill one in the plastic, from inside the telephone, in the centre of the post, with a 7 mm metal drill bit. Close the padlock (combination or key, not included) on the furniture or anchor-point side, never on the telephone side.

Step 5: hook switch
On the telephone's old circuit board, find the hook switch: it is a very tall component, with a small moving part on top. Desolder it from that board and solder it onto the "COMBINE-D2" footprint 3 of the kit's circuit board.

Step 6: rotary dial or push-button keypad
First cut off the lugs at the end of the wires, strip each wire over a few millimetres and tin it (a thin layer of solder with the soldering iron): otherwise, the wires will not hold in the screw terminals.

Rotary dial
Screw the 4 wires of your rotary dial into the "ROTATIF" terminal 4, then set switch 6 to OFF:
- GND: the two two-coloured wires;
- D3: the blue wire;
- D4: the red wire.
Push-button keypad
Screw the wires of your keypad's matrix into the "CLAVIER" terminal 5, then set switch 6 to ON:
- V1 to V3 (D3 to D5): the columns (vertical);
- H1 to H5 (D6 to D10): the rows (horizontal).
The S63 Keypad Board
A "matrix" keypad connects a column (V1 to V3) and a row (H1 to H5) when a key is pressed: the program recognises the key at that crossing. Some original S63 keypads are not wired this way. For them, the S63 Keypad Board replaces the original circuit while keeping your keys: the key block of your old keypad clips onto it.

Two models of old keypad fit it, one square, the other round. Before ordering it, send me a photo of your keypad: I will tell you whether it is compatible.
It comes with an 8-way screw terminal, soldered underneath: you cannot see it from the top. To install it:
- unclip the key block from the old circuit, then clip it onto the top of the keypad board;
- clip the keypad board into the telephone, in place of the old circuit: its two top slots and its two lugs, on the right and on the left, fit onto the same small plastic or metal clips;
- connect its terminal to the "CLAVIER" terminal 5 of the kit's circuit board with 8 wires, each on the terminal with the same name: V1 on V1, V2 on V2, and so on up to H5 on H5;
- set switch 6 to ON.
Keys 1 to 9 and 0 dial the numbers. The *, # and "R" keys do not correspond to any digit: they do not play any sound. The "R" key only exists on some keypads, on the left or on the right: the keypad board has a place for each of the two cases.
Step 7: handset and earpiece
First put back the original 4-hole plastic part, with its small partitions, between the kit's circuit board and the lugs (old telephones usually have one): it keeps the lugs nice and straight, without touching each other. This is very important: a short circuit between two lugs destroys the audio player.
Then, using the original screws and lugs, connect the handset wires to the lugs 8: blue on "−", red on "+", both green wires on "MIC". If your telephone has an earpiece, its two wires, a red one and a blue one, connect to the same place as those of the handset: blue on "−", red on "+".
To let people listen on one or more headphones, now is the time to plug the headphones, or a splitter, into the "LINE" jack socket 9: the sound there is in stereo.

Step 8: metal bracket
Screw the original metal bracket back on: it fits both into the notches of the hook switch 3 and onto two screws, whose nuts are under the base of the telephone.
Step 9: microSD card and content
Put one or more sounds, preferably in MP3 format (or WAV, up to 48 kHz / 16 bits), into a folder named "mp3". Name the first one "0001", then "0002" and so on, without skipping a number. Once done, insert the microSD card into the reader 2.
Step 10: settings
Choose your settings with the six switches 6 (see above), and set the volume 7.

Step 11: power supply
Plug your 7 to 16 V power supply into the socket 1, without plugging the power adapter into a wall socket yet.

Step 12: first test
Plug the power adapter into a wall socket and look at the Nano: its small red light should come on.
Then unplug the power adapter from the wall socket, whether the light came on or not.
If it stayed off, there is probably a short circuit somewhere: clean and check the lugs, the wires and the solder joints, then try this test again. If it still does not come on after several attempts, contact me and send me a photo of your assembly, ideally of the top and the underside of the kit's circuit board.
Step 13: closing
Turn the telephone over again on the tea towel and close it with the two screws underneath: the kit's circuit board can no longer be reached. Then put the telephone the right way up, on its feet, as for normal use, and put the handset back on its cradle, together with the earpiece.
First use
First test
- Plug in the power supply and wait 5 seconds.
- Pick up the handset and listen.
- Magic!
If nothing happens
- Unplug the power supply.
- Check the microSD card: formatted in FAT16 or FAT32, an "mp3" folder at the root, files named "0001", "0002"… without gaps, and nothing else.
- Check the connections of the hook switch 3 and of the handset 8, then the volume 7.
- Plug back in, wait 5 seconds, and pick up the handset.
Ideas & Recommendations
- When the handset is picked up, the sound starts immediately. Slow people may therefore miss the beginning of your file. So I recommend adding 1 to 2 seconds of jingle before your file. Silence is not enough, because people who pick up quickly might think the device is not working. The jingle lets them know that the file is about to start.
- Sometimes the telephone has an earpiece at the back. It may seem a good idea, so that two people can listen at the same time. However, you will quickly notice that some people use the back earpiece without picking up the handset. Since it is the handset that starts playback, these people will hear nothing. So I recommend simply removing this earpiece.
- Because it is sometimes better to guard against theft, an anti-theft sling is easy to fit on a desk S63 (see step 4 of the installation). Add a simple combination or key padlock (not included). You can also extend it (sold in packs of 10).

Advanced use
Random explained
Although true randomness does not exist in computing, I am rather proud of mine and would like to explain it:
To prevent the (bad) luck of randomness from playing the same sound twice in a row (which is statistically possible, and frustrating), my program counts the number of files on the card, then plays them all at random, without repeating a single one until they have all been heard. Once the list is used up, it makes a new one, and so on.
Nano
The Télé'Son is controlled by a Nano. So it is perfectly possible, and easy, to create your own program. So have fun! Here are its pins, as my program uses them:

You can also get help from the DFPlayer Wiki.
Have an idea and want to know whether it can be done, and how? Feel free to contact me!
Problems & Solutions
While the DFPlayer is a brilliant little player that powers many of my creations, including this one, it has many small flaws that are nevertheless easy to work around. So here is an article dedicated to solving all the problems of the DFPlayer Mini.
Versions
Every time I launch a new production run of circuit boards, I make a few changes to the design. Feel free to send me your suggestions for the next versions.
- October 2023 - V1: For rotary dial telephones only. Bug with the ringer. Can only fit certain versions.
- February 2024 - V2: Added push-button keypad telephones (matrix). Ringer bug fixed. Can fit all "desk" Socotel S63.
- January 2025 - V3: Can fit "wall-mounted" Socotel S63.
- November 2025 - V4: 7 to 12 V power supply possible, two jack sockets added ("Line" and "3W").
- November 2026 - V5: 7 to 16 V power supply, large capacitor acting as an energy reserve for loud sounds, footprint for the handset microphone (not fitted on the kit). The "3W" socket is no longer fitted.
Conclusion
Using this Télé'Son is really simple but, at the risk of repeating myself: feel free to contact me if you have the slightest question or suggestion about it!