The Exten'Son is a small round board that adds up to 10 buttons to your Exposi'Son or your Ambi'Son. The resistors are already soldered: all you have to do is screw in your buttons. It is sold in the BigSoundBank shop.
With two Exten'Son, an Exposi'Son can play up to 14 sounds, and an Ambi'Son up to 20, each button playing its own.

Overview
My players can recognise several buttons on a single wire, called "AdKey": each button goes through a different resistor, and the player knows which one you pressed from the voltage it receives. To save you soldering these resistors, I designed the Exten'Son, which I solder myself.
- It has 10 screw terminals, B1 to B10: one button per terminal.
- An "AdKey" terminal connects it to one of the two AdKey terminals of your player. One Exten'Son per terminal, so two at most.
- It has no active component and no power supply: it consumes nothing, and there is nothing to program.
- It is round, 40 mm in diameter, like the Exposi'Son, with two 3 mm mounting holes.
- It is sold as a bare board, without wires or push buttons.
Whether you are a user or a tinkerer, feel free to contact me if you have any questions about it!
Warning
Caution: the board comes without a case. Nothing conductive must touch the circuit board: risk of a short circuit. Connect it only to an AdKey terminal of an Exposi'Son or an Ambi'Son, never to a power supply. On an Ambi'Son, it only works with the AdKey option (see With an Ambi'Son).
In detail

Key
The diagram shows the V1.2 board, seen from above.
- 1: ten screw terminals, B1 to B10, one per button. Their name is printed next to them on the board.
- 2: nine resistors, already soldered, from 3 kΩ to 200 kΩ, one per button from B2 to B10. B1 does not need one.
- 3: "AdKey" terminal, to connect to the AdKey terminal of your player (the AdKey wire and ground).
- 4: two 3 mm mounting holes, one in the centre, the other at the top right.

To mount it in your case: two 3 mm holes, one in the centre of the board, the other 34 mm from the left edge and 11 mm from the top edge. I do not supply spacers: plan for 3 mm screws and spacers.
How many Exten'Son, and on which terminal?
Your player has two AdKey terminals, "1" and "2". An Exten'Son does not do the same thing on one or the other:
- On AdKey 1: its buttons play files 1 to 4, and the others control playback (previous, next, pause, loop all…).
- On AdKey 2: its ten buttons play files 5 to 14.

The right choice therefore depends on the number of sounds to play:
- Up to 4 sounds, with control buttons as well: one Exten'Son on AdKey 1.
- From 5 to 10 sounds: a single Exten'Son is enough, on AdKey 2. No need to buy two to get 4 sounds on the first and 6 on the second. Its buttons then play files 5 to 14: on an Exposi'Son, first copy 4 dummy files (silences, for example) to the microSD card, then your sounds; on an Ambi'Son, simply name your sounds 0005 to 0014.
- More than 10 sounds: two Exten'Son, one on each terminal. Up to 14 sounds and the controls; and on an Ambi'Son, up to 20 sounds if you ask me (see below).
With an Exposi'Son
Connect the "AdKey" terminal 3 of the Exten'Son to terminal "1" or "2" of the Exposi'Son, with two wires: AdKey to AdKey, ground to ground. Then connect a button to each terminal B1 to B10 you need.

- The files are numbered in their copy order on the microSD card: copy them one by one, in the order you want. The details are in the Exposi'Son user manual.
- The "Play" button of the Exposi'Son does the same as button B1 of an Exten'Son connected to terminal "1": it plays file 1.
- Short press, long press: on terminal "2", a short press plays the file once, a long press plays it in a loop. On terminal "1", a long press on B1 plays file 1 in a loop, and on B5 and B6 it sets the volume.
- B9 does nothing on the Exposi'Son. B10 switches from interruptible mode (a new press stops the current sound) to non-interruptible mode (the current sound plays to the end), and back.
With an Ambi'Son
On the Ambi'Son, the Exten'Son connect to the four-pin "AdKey" terminal, which groups the two inputs: AdKey 1 and its ground on one side, AdKey 2 and its ground on the other. This terminal is part of the AdKey option, to be chosen when ordering the Ambi'Son.

- The AdKey option is essential: besides the terminal, it includes two 10 kΩ resistors, without which the Ambi'Son would play files on its own. These are very small surface-mounted components, hard to fit without experience. If your Ambi'Son does not have this option, send it back to me: I will add it.
- The program: it is the Ambi'Son's Nano that reads the Exten'Son, and its program sets what each button does. I deliver it set up for 14 files and controls: on AdKey 1, files 1 to 4, previous, next, play / pause and "loop all files" (B9 and B10 do nothing); on AdKey 2, files 5 to 14.
- 20 files on request: if you would rather have each button play a sound, tell me when you order, and I will set the program up for 20 files: AdKey 1 then plays files 1 to 10, and AdKey 2 files 11 to 20.
- The files are called by their name, in the "mp3" folder: 0001.mp3, 0002.mp3, and so on, whatever the copy order. The details are in the Ambi'Son user manual.
- One button, one sound: each press plays its file once.
Beyond 20 buttons, the Ambi'Son accepts up to 8 Expan'Son, that is 128 buttons: it is another board, described in the Expan'Son user manual (in French).
Connecting the buttons
- One button per terminal: connect the two wires of the button to the two screws of a terminal B1 to B10, either way round. Only use the terminals you need.
- The wires: 0.13 to 1 mm² cross-section, stripped over 5 to 6 mm, slid into the side of the terminal and tightened by the screw on top. Avoid wires that are too long, both between the player and the Exten'Son and between the Exten'Son and the buttons.
- Which buttons? Any push button will do, of any size: an old button, the one on the device you are fitting… I also sell push buttons, delivered wired to the length you need, ready to screw onto the Exten'Son.
- One button at a time: the player recognises the button by the voltage; two buttons of the same Exten'Son pressed together give another voltage, and the player may play the wrong sound.
Problems, Solutions & Ideas
- No button does anything: check the cable between the Exten'Son and the player (AdKey to AdKey, ground to ground). On an Ambi'Son, check that it does have the AdKey option and that its program is set up for the Exten'Son.
- A button plays the wrong sound: on an Exposi'Son, it is almost always the copy order of the files; reformat the microSD card and copy the files again one by one, in order. On an Ambi'Son, check the file name (0005.mp3 for the fifth).
- A button plays nothing on an Ambi'Son: the matching file is probably not on the card; the button is then ignored.
- Sounds play on their own on an Ambi'Son: the two resistors of the AdKey option are missing.
- For any other question or idea, contact me.
Versions
- V1: first board, abandoned: button 1 was not connected.
- V1.1: error fixed.
- V1.2: current version, with the same connections as V1.1. Only a few texts change on the board.
Conclusion
The Exten'Son is probably the simplest of my boards but, at the risk of repeating myself: feel free to contact me if you have any questions or suggestions about it!